Belt-Type Oil Skimmer (Basic Model)

OILSEIZER® Belt-Type Oil Skimmer (Basic Model) Equipped with a small size gravity oil/water separator that finely demonstrates as a secondary separation polishing device, KOS-B series has become known as a preferential and universal choice in most oil/water separating applications because of its high usefulness and cost-efficiency, especially in removing or recovering floating oils from the surface of water or solutions. For adequate skimmer operation, various sorts of lubricants for motors or machineries, fats, oil and grease (FOG) should all be immiscible and in a free-flowing state. Also, for more effective oil skimming capability, the water surface needs to be stable and oil droplets, mechanically and temporarily suspended in the water, be allowed appropriate time until they freely rise up to the surface before oil droplet-laden water lastly moves away as effluent. Also called an oil recoverer or oil remover. Removal of chemically emulsified oil and semi-solid grease or fat requires using another device. How it works The motor-driven head pulley turns and moves the oleophilic belt around the circuit from the head pulley to the tail pulley below water, so that the belt can enter and exit the water to continuously contact with surface oil layers. Oil sticks to both sides of the rotating belt and gets wiped out as the belt passes through two bisymmetric wiping blades. Wiped oil flows to the small size oil/water separator through the oil trough. Virtually water-free oil and oil-free water discharge from the skimmer through two different outlets of the separator.   Features - Rugged construction, simple installation, least installation space - Several models: treat different hourly peaks of oil influx as one of standards for selection of skimmers - Small size gravity O/W separator: provides secondary separation of even small amount of water mixed in the oil when skimming, has two discrete oil and water outlets, and is easy to remove deposited sludge. - Material: Stainless steel or powder coated steel - Screen cover: allows instant observation on how the belt moves and oil being wiped off, whenever required - Adjustable wiper blades: closely contact with both belt surfaces at the same time - Oil- and wear-resistant wiper blades - Uninterrupted skimming operation regardless of fluctuating water level - Simple belt replacement - Pulley yoke with chain: prevents a tail pulley from deviating or falling off - Belt: endless, made of chemical resistant poly or stainless steel as an option for special application in hot liquid above 80? - Motor cover: an option protects against direct rainwater and sunray in outdoor installation   Specifications Model KOS-B0512 KOS-B1012 KOS-B1020 KOS-B2020 Remarks Oil Removal Rate (per hour, max. ) 23l 45l 100l 200l motor oil #30 at room temp. Gearmotor 40W 60W 90W 90W volt, ph. & hz. as required Head/Tail Pulley Dia. 120? 120? 200? 200? yoke/chain included Belt Width 50? 100? 100? 200? length oneway from 300? min. Small Size Gravity Oil/Water Separator 4l 5l 18l 20l secondary O/W separation Outside Dimension (W x H x D)   390x440x355   390x440x405 490x610x455 490x610x555 (?)  - Pre-installation considerations hourly peak of oil influx, sort of oil (floating, free-flowing), tank (aboveground or underground), height of skimmed-oil collecting container, lowest water level, water temperature, electric voltage, etc. - Support stand, installation, and electric wiring: excluded from the scope of supply unless otherwise expressed in writing    Options - Skimmer housing material: stainless steel (SS304) or power coated steel - Belt length: min. 300? (measured from the skimmer base down to the tail pulley center), in an increment of 300? up to 3000? (longer belt available subject to prior consultation) - Motor electricity: 220V, 380V, 440V, 50Hz, 60Hz. Other voltage available subject to prior consultation. One phase motor comes with an illuminated rocker switch as standard while three phase motor with lead wire or terminal box only - Motor cover: direct rainwater- and sunray-resistant - Timer, support stand frame    Applications - Removal or recovery of various floating oil - Oil/Water separators, wastewater treatment, carwashing plant, parking lot - Heat treatment/quenching - Automobile/railway maintenance workshop - Pre-paint and pre-plate degreasing - Foodstuff and fishery processing plant - Part washing tank/pit, metal forming coolant tank - Steel mill, iron mill, oil refinery, chemical plant, oil reservoir * You will find more information from our website www.kum-in.co.kr. * For technical improvement, design and specifications are subject to change without prior notice.