Features of 5000 series
1. Can be referred to as aluminum and magnesium alloys. Magnesium content between 3-5%.
2. Non-heat-treatable alloy
3. Low density, high tensile strength and elongation rate. Good corrosion resistance,weldability and cold workability.
Technical standard
National standard (GB/T 3880-2006)
The application scope of 5083 aluminum plate
5083 aluminum plate is often used in materials for ships, vehicles, cars and aircraft plate weldments pressure vessel, which is to be strict fire prevention, cooling device, television tower, drilling equipment, transportation equipment, missile component and armor.
The chemical composition of 5083 aluminum plate
Al: aluminum allowance Si: 0.4 or less Cu: 0.1 or less Mg: 4.0-4.9
Zin: 0.25 Mn: 0.40-1.0 Ti: 0.15 or less Cr: 0.05-0.25 Fe: 0.4
Individual: 0.05 Total: 0.15
The mechanical properties of 5083 aluminum plate
Tensile strength:sb (MPa):110-136
Elongation delta:d10 (%): =20
Annealing temperature: 415 °C.
Yield strength:ss (MPa) =110
Elongation rate: d5 (%) =12
The application scope of 5052 aluminum plate
5052 aluminum plate is mainly used in the request high plasticity and good weldability, working in a liquid or gas medium low load parts, such as tank, gas or oil duct, and other various liquid containers made of deep drawing parts: small load wire used for rivet. Also commonly used in the transportation vehicles, ships, sheet metal parts, instrument, lamps stent and rivet, metal products, electrical enclosure, etc.
Chemical composition of 5052
Al: allowance; Si: 0.25; Cu: 0.10; Mg: 2.2 ~ 2.8;
zinc: 0.10; Mn: 0.10; Cr: 0.15 ~ 0.35; Fe: 0.4 0.
Mechanical properties of 5052
Tensile strength (sb ):170~305MPa
Conditions to yield strength: s0.2 (MPa)=65
Modulus of elasticity: (E) : 69.3 ~ 70.7 Gpa
Annealing temperature: 345 °C.
The surface quality
1, the surface is not allowed to have crack, corrosion spots or nitrate.
2, on the surface, allowing a depth of no more than 8% of the nominal size peeling defect part wall thickness, air bubbles, surface roughness and the local mechanical damage, but the defects cannot be more than 0.5 mm, maximum depth defect sheet with a total area of no more than 5% of the total area.
3, allow the supplier polishing along the longitudinal profiles until the surface is smooth.
4, other requirements: disucssed by both sides.
Size of the sheets
Alloy grade
Temper
Thickness(mm)
Width(mm)
Length(mm)
5A02(LF2)5052
O(M)
0.3-10
1000-1500
=6000
H14/24(Y2)
0.3-6.5
1000-1500
=6000
H18/28(Y)
0.3-4.0
1000-1500
=6000
F.H112(R)*
5-80
1000-1600
=6000
5A03(LF3),5A05(LF5)5A06(LF6),5154,5154A,52545083
O(M)
0.5-4.5
1000-1500
=6000
F.H112(R)*
5-50
1000-1600
=6000
5051 5052 5083 5005 aluminum sheet/plate
Description
Product Inquiry
Purchase Product Catalog
Payment & Shipping Conditions:
- Payment: We accept payment through Paypal Only.
- Shipping: We will ship the catalog once the payment is received. And you will be receiving the catalog with in 10 -14 busines days. Shipping might be delayed in due to international shipping conditions which is depends on the countries receiveing. In case hard copy of catalog is not available then we will ship the soft copy.
- Refund: We can refund the order before shipping process was initiated. Incase Catalog not available, we will make sure to refund the order.
- Note: This is a Catalog Produt.
Share 5051 5052 5083 5005 aluminum sheet/plate in Social Media