-
Auto Gate Valve-WITH CONTROLLER
<img src="http://www.bestmadeinkorea.com/photo/2015/jc/Auto-Gate-Valve-WITH-CONTROLLER-01.jpg" alt="Auto-Gate-Valve-WITH-CONTROLLER-01.jpg" >
** Application
- Etcher
- CVD(Mo, LP, HDP, PE)
- Sputter
-
-
dtr newly developed carbibe hobs can cut gears down powerfully at high speed which brings higher effeciency.
of production than conventional hss hobbing.
charcterstics:
1.high cutting speed
2.short machining speed.
3.a longer tool life than conventional hss cutters.
4.time saving per price for gear manufacture.
5.high
-
the teeth and body are assembled separately and with different materials.
advantages:-
1.the cutting control is efficient controlled relief life.
2.cost effective with lower material price for body.
3.useful for high speed cutting with controlled arbor.
disadvantages:-
1.the manufacturing process is complex
2.the out-parameter
-
increasing productivity:special hss and multi layer coating increasing cutting ability more than 2 times compared to convential hob.
cost savings:increase tool life and reduced cycle time lead to cost saving efficiencly.
friendly to environment:production without cutting oil.
sucessful results require:need a good bobbing m/c for turbo
-
Traditionally, profile and lead inspections have been indispensable portions of a standard inspection of an involute gear. This also holds true for the worm of a worm gear drive (Ref. 1). But the inspection of the profile and the lead is rarely performed on a worm wheel. One of the main reasons is our inability to make good definitions of these
-
a worm is designed based on worm shaft specifications.their are no standards for worm gear specifications.
generally hob is manufactured as zk type.
Gleason Cutting Tools Corporation makes all types of HSS hobs for throated worm gears which mate with non-enveloping worms: single or multiple-thread, shell, shank or clutch-driven, topping or
-
Splines are ridges or teeth on a drive shaft that mesh with grooves in a mating piece and transfer torque to it, maintaining the angular correspondence between them.spinner gear is used when the power transmission is same direction
For instance, a gear mounted on a shaft might use a male spline on the
-
Out diameter and tolerance for parallel side spline.
root diameter and tolerance for parallel side
the width and tolerance for parallel side spline.
no of tooth for parallel side spline
standard and type of hob
amount of grinding when grinds during
-
BELT SPECIFICATION
BELT MAKERS INSTRUCTIONS
NT OF PULLY
PULLY PROFILE
HOB
-
STANDARD FOR CHAIN ASA1 AND ASA2
PICH FOR CHAIN
ROLL FOR DIAMETER
NO OF CHAINS
SPECIFICATIONS FOR ARBON WHICH USES CUSTOMER
-
A gear or cogwheel is a rotating machine part having cut teeth, or cogs, which mesh with another toothed part to transmit torque, in most cases with teeth on the one gear being of identical shape, and often also with that shape on the other gear.[1] Two or more gears working in a
-
A gear or cogwheel is a rotating machine part having cut teeth, or cogs, which mesh with another toothed part to transmit torque, in most cases with teeth on the one gear being of identical shape, and often also with that shape on the other gear.[1] Two or more gears working in a
-
Hobbing is a machining process for gear cutting, cutting splines, and cutting sprockets on a hobbing machine, which is a special type of milling machine. The teeth or splines are progressively cut into the workpiece by a series of cuts made by a cutting tool called a hob. Compared to
-
Indoor 24-Hour Time Switch (standard)
Energy Save
Type: Indoor-installable
Model: SK-24H-A401
Rated Voltage: 220V/16A
Working Frequency: 60Hz
Motor Load: 3A(40W fluorescent tubes: 30 units or less)
Main Application: Automatic control of indoor signs or fluorescent aquarium lights
FEATURES
The switch is safely used
-
Automobile Parts:
TRANSAXLE PARTS
Detent Sleeve
Blocking Pin
Disk M / Shaft
Strain Rod
Dowel Pin
Shaft
CYLINDRICAL ROLLER BEARINGS
(T/ M)Roller Bearing ASM CHT
Needle Roller Bearings
Thrust Bearings
BEARINGS
T/M Roller Bearing ASM
-
Tapered Roller Bearings
Tapered roller bearings are designed so the apices of the cones formed by the raceways of the cone and cup and the conical rollers all coincide at one point on the axis of the bearing. When a radial load is imposed, an axial force component occurs; therefore, it is necessary to use two bearings in opposition or
-
Spherical Roller Bearings:
HS Bearings, which offer particularly high load-carrying capacity, high limiting speeds, and are highly functional under high-temperature operating conditions of up to 200°C. From heavy gear and caster applications to the harshest aggregate and conveyor systems, HS Bearing sphericals stand ready to help
-
Fork-Lift Truck Bearings:
Installed on more than 1,700,000 forklifts over the past 20years, our bearings have been used under various environments in numerous countries around the world and have gained high marks for their quality.
Various items for 0.5-ton to more than 25-ton fork-lifts are designed, produced and tested in-house for
-
-