-
This product is a cold-setting epoxy adhesive. It is made by mixing special fillers with epoxy resin for
heat resistance, and enables the adhesion of inductor/resistance lead
-
[Adhesive for old and new concrete]
This product is a cold-setting epoxy adhesive for old and new concrete. It allows an airless spraying method when additional concrete is applied to hardened
-
[Putty for construction]
This product is a two-component cold-setting high-viscose epoxy adhesive, and ensures great
-
[Epoxy resin mortar]
This product is an aliphatic two-component cold-setting oil epoxy resin for high-strength resin mortar
-
KNS MAXUM PLUS TRANSDUCER
Transducer for KNS MAXUM Wire Bonder
Spec: Impedance 14~25 ohm, Frequency 113.0~115.0
-
[Water epoxy paint]
This product is an aliphatic modified two-component cold-setting water colored paint. It is used as a water paint.
Product Types
Code Name
SC 616A
SC 616B
SC 616C
Product Name
Water epoxy primer
Water epoxy colored paint
Water tar-epoxy
-
[Delamination and reinforcement of fibers]
This product is an aliphatic modified two-component cold-setting oil solvent-free transparent epoxy product. It enables the laminated reinforcement of glass fibers in concrete
-
[Oil epoxy paint]
This product is a cold-setting oil-soluble colored pure epoxy paint. It is used as a non-slip paint for
-
This product is a one-component heat setting epoxy adhesive, which is hardened by heating at a low temperature. It enables the adhesion of syringe needles or electronic
-
[Adhesive for old and new concrete]
This product is a cold-setting epoxy adhesive. It is used when additional concrete is applied to hardened concrete or when concrete is
-
[Putty for construction]
This product is a two-component cold-setting high-viscose epoxy adhesive, and ensures great adhesiveness on wet or submersed
-
[Epoxy resin mortar]
This product is a coal tar-modified aliphatic two-component cold-setting oil solvent-free tar epoxy
-
KNS MAXUM TRANSDUCER
Transducer for KNS MAXUM Wire Bonder
Spec: Impedance 14~25 ohm, Frequency 113.0~115.0
-
Carbon Paper
Material: Chopped carbon fiber(3~12mm)
Process: dissolication -> web -> drying -> heat-treatment
Application: WC sintering, Fuel-cell, Gas Diffusion
-
â–¶ WC tip bonded to enhance the surface wear resistance of conventional steel tappet
â–¶ Patented Chemistry of WC to bond 2 different materials (WC, and Steel)
â–¶ Application: Tappet (Diesel engine
-
WC Rod used for WC tools
â–¶ Rod shape material (OD:Ø1~50, Length: Max330mm)
â–¶ Wear-resistant materials for industial parts
â–¶ Application: Drill, Micro Drill, Endmill, and various industirial
-
WC Powder For Thermal Spray
â–¶ WC Base used for thermal spray process
â–¶ Homogeneous powder size distribution, and good flowability
Application: HVOF, PTA, Laser Cladding, 3D
-
Bonding Sheet (Tool PAD) When you want to performs task such as PCB bonding to connect the PCB and film bonding to connect the TAB(Tape Automated Bonding) coe(chip on Glass) bonding, CORChip on film) bonding, and panel glass of the manufacturing process of the module, and pressure buffering effect through a direct connection to the Toorrip It Is
-
Bonding Sheet
Using the ACF(Anisotropic Conductive Film) from LCM Module Process of FPC and TFT-LCD, and is used for applications that are mounted PCB Ass'y and Drive Ass'y, the Panel Ass'y. and Tool from the heat of the TCP, PCB protects and heat pumping is used as a buffer sheet.
It is used as an insulating thermal pad sheet,
-
Bi-Metal Bearing containing lease than 4% of lead(Pb) satisfying