-
· Use : 1.This sensor is used in water flow sensing. 2.This sensor has application to gas boiler and instantaneous warm-water appliance and water filtering appliance. · Features : 1.This sensor has excellent character in low pressure. 2.The out pulse frequency has linear character in flux change. This sensor has a half-permanent life by high
-
Audiometric booth
This is Standard single size Audiometric booth used in ENT hospital, clinic, hearing aid shop, examination center of industry, etc. Ventilating system has installed for pleasant environment. It is possible to move easily as assembly furniture and has got own wheel caster with breaking system. Location of door and window can be
-
A. System Platform
The Dynamic MR Plus™ is a 2D image feature which enhances detection and contrast resolution while decreasing speckle echoes.
Dynamic Range is the ratio of the brightest portion of the image to the darkest. The Wide Dynamic Range (WDR) function has been developed to
-
A. Specification & Composition
1. Magnet Subsystem - 1 set
1) Magnet
- Field Strength: 1.5 Tesla
- Active shielded Superconducting Magnet
- Dimensions
- Maximum Height: 2400 mm
- Length : 1570 mm
- Cryogen Boil-off rate < 0.065
-
A. Feature
With its variable range of system components you can design your own system to meet the needs of your application.
The system modules can be assemabled in such a way to use either a single or dual flat panel detector to fit in any medical environment form small clinic to large medical
-
A. Feature
Combining extreme mobility with easy handling and high image quality our IZI line will provide you with full range of Mobile X-Ray systems.
The Systems also can be used with battery to increase productivity and meet all your mobility needs.
B.
-
A. Feature
Get two steps ahead in Preventive Care with kidney-friendly scanning and low dose early detection.
Get two steps ahead in Freezing Motion with "free-breathing" CT imaging and the industry's fastest, most versatile scan mode.
Get two steps ahead in
-
A. Feature
Large C-Arm size for easy use on clinical environment
Boost fluoroscopy for special vascular angiographic examination
High power output with 2.2kw HFG(no high voltage cable)
High grade x-ray tube which improve image quality and 0.5/1.5mm focal spot
-
The equipment automatically and periodically measure property values constant temperature chamber without manual process by implementing constant temperature chamber and measuring instrument for evaluating reliability of high output LED unit and module.
Reliability test
ㆍDurability test: Measure properties of
-
Measure all performance items necessary for KS and certification. High performance and low cost equipment (Patent registration in progress)
floor plan
Measuring
-
Measurement for base data of optical and electrical conversion efficacy to figure out which electrical signal detector such as solar cell outputs for radiance exitance or illumination by each wavelength.
Key features
ㆍMeasuring targets : Solar cell, silicon and optical diode
ㆍChannel : 4ch auto
-
I-V CURVE meter dedicated to solar cell. Current measurement for various types of solar cell : Measure polarizations for 20A Measure Series resistance Rs, and parallel resistance Rsh
Key features
ㆍI-V CURVE meter dedicated to solar
-
Detect find crack of solar cell module-EL tester. Test efficacy among Cells/Strings of solar modules, Patented light source- Transferred technique from KRISS
Measuring items
ㆍDetect find crack of solar cell module - EL tester
- Imagery interpretation by infrared ray : 1sec / cell
- Detect fine crack:
-
Calculate the highest percent flicker and flicker index by measuring average optical power of lamp
Technical Specifications
* Photo diode : silicone photodiode, effective section area :100mm2, Mismatching factor : f1’<1.5% Class L
* Equipment Sampling Rate : 5 kHz
* Calculate Flicker Index and
-
Equipment to measure electrical and optical properties of LED epi wafer at the same time.
Measure EL property of LED epi
ㆍMeasure electroluminescence of LED epi wafer.
ㆍ Measure upper/lower illumination of wafer by using glass.
ㆍHas measuring sensors in upper and lower
-
It is program that automatically counts the number of chips with features; video processing speed : 10 sec/ 2inch wafer, input of model name, serial number, operator name, set up, save, open and modify condition for various chips.
Measurement via scanning
ㆍOptical resolution: 4,800dpi×9,600dpi (with
-
Easy to measure various items, User interface (Support on-demand SW design), integrated measurement of optical, electric
-
Measurement and data usability with consideration of user convenience in quality inspection, R&D, and reliability test.
Simultaneous measurement of optical properties/Electrical property
ㆍSimultaneous measurement of optical properties/Electrical property by one click.
ㆍHigh sensitivity and
-
Measure optical/electrical/thermal properties for various high output, multi-chip, and module LED/OLED as well as current stressing and measurement. Support up to 3A and consecutive/pulse type
Measure performance of high output, multi chip LED/OLED
ㆍMeasure optical/electrical/thermal properties for various
-
Connect various mass-production equipment (Sorter.Prover.Handler) to tester. Provide user friendly interface and Under Photometer function. Automatically save collected data as Excel file and statistical processing.
Specificatons
Peak / Dominant Wavelength
p, d
Refer to LEOS(OPI-100)